Creality SPARKX i7 Nano Combo

SPARKX i7 3D printer with the compact CFS nano for up to 4-colour printing: spools hang on the frame, one feed unit sits on top, with auto load, auto refill and run-out detection. 260 × 260 × 255 mm build. Listed at PrototypeBD for buyers in Bangladesh. Browse more 3D printers.

Key features

CFS nano: four colours in a small footprint

The CFS nano is a small 4-slot feed unit (127 × 85 × 65 mm, 445 g) that mounts on the i7. The spools sit on holders on both sides of the frame, so Creality puts the set at 550 mm wide instead of 876 mm with a separate box, a 37 % smaller width. Insert each filament once and the CFS nano loads and unloads it, and it switches to a backup spool when one runs out.

What the CFS nano kit adds

The kit is the CFS nano unit with its spool arms, stands, spool hubs, PTFE tubes and connection cable. It runs from the printer over an RS 485 cable, so no separate power supply is needed. Storage is open, and filament tangle detection is not supported on the CFS nano.

Quick-swap hotend, extruder lever and cutter

The hotend, extruder lever and filament cutter are each built to be swapped by hand. Creality says the nozzle can be safely hot-swapped in about five seconds, so you can move to a 0.2 mm nozzle for fine detail or 0.6 / 0.8 mm for faster prints. Bed leveling, nozzle Z-offset and input shaping run by themselves before each print, and leveling only probes the area your model will use, so it finishes faster. Pressure advance and input shaping keep corners sharp and walls free of ringing at speeds up to 500 mm/s.

Same i7 printer

The Nano Combo uses the full SPARKX i7: up to 500 mm/s, 300 °C hotend, 100 °C PEI bed, AI camera with privacy cover, RGB status light and Night Mode.

CFS nano or CFS Lite?

Both give four colours. The CFS nano is smaller and open, and works with PLA, PETG and PLA-CF. The CFS Lite in the Color Combo is a sealed box with desiccant and RFID recognition, and also takes TPU 64D. Choose the Nano Combo for a tight desk and the Color Combo for humid rooms or long-term spool storage.

Good for

• Small rooms and desks where a side box will not fit

• Multicolour PLA and PETG prints for gifts, signs and models

• Buyers who want four colours at a smaller footprint

What's in the box

Creality does not publish a packing list for this exact set on its product pages, so PrototypeBD confirms the box contents with you before you pay. The set is the SPARKX i7 printer and one CFS nano kit; Creality notes it may ship either as one Nano Combo box or as the i7 plus a separate CFS nano kit.

Before you order

• Price: contact us for the current price. This model is listed for pre-order.

• Filament is not included. Creality states that filaments are sold separately; spools in the photos are for illustration. See our filament range.

• Power: Creality rates the SPARKX i7 for 100–240 V AC, 50/60 Hz (700 W at 220 V), so it runs on Bangladesh 220 V mains. Ask us about the plug type of the unit you receive.

• Creality: the i7 Nano Combo ships in two forms, as one Nano Combo or as the i7 plus a CFS nano kit. Only the Color Combo ships fully assembled, so expect to fit the CFS nano.

• CFS nano filaments: PLA, PETG and PLA-CF.

Prefer a sealed box with RFID, refill only, or the printer alone? Ask us about the SPARKX i7 Color Combo, i7 Autofill and SPARKX i7. Browse all Creality printers and 3D printers.